Physics · Courses in this subjectExpandCollapse

Secondary physics formula toolkit

PhysicsSuggested ages: 12–18

What should you check after remembering an equation?

Explore ten common equations through force, motion, energy, density and circuit controls. Original diagrams connect units, signs and conditions, with worked examples that catch common errors.

Learning goals

  • Distinguish symbols reused in different equations and state their SI units.
  • Vary one parameter to compare direct, inverse and squared relationships.
  • Check conditions before substituting, then check units and magnitude.

Before you begin

  • Use multiplication, division, squares and unit conversions; recognise force, mass, distance, time, current and voltage.
  • The mechanics extension uses signed direction and cosine. Start with pressure, average speed, density and Ohm’s law if these are new.

Physics formula explorer

Choose a topic, then check units and conditions before using its equation. Open any topic to change its parameters; each has its own link.

Levels are suggestions. Curricula vary; work, energy and Newton’s laws can also extend lower secondary learning.

Newton’s second lawUpper secondary mechanicsFₙₑₜ = ma

Net force changes velocity. For a fixed mass, a larger acceleration requires a larger net force.

Link to this topic
Newton’s second lawThe green arrow represents net force Fₙₑₜ. Changing a can reverse it; changing m changes its length. m Fₙₑₜ +−
The green arrow represents net force Fₙₑₜ. Changing a can reverse it; changing m changes its length.

One-dimensional sign convention: right is positive; left is negative.

Change the parameters
Calculated resultFₙₑₜ = 6 N

Symbols and SI units

Fₙₑₜ: net force, N; m: mass, kg; a: acceleration, m/s².

Unit check

kg × m/s² = N

When it applies

Use in an inertial frame for constant mass in classical mechanics. Fₙₑₜ is the vector sum of external forces, not an arbitrary single force. Here we calculate one-dimensional components.

Worked example

3 kg × 2 m/s² = 6 N. Zero net force means zero acceleration, not necessarily zero velocity.

MomentumUpper secondary mechanicsp = mv

Momentum combines mass with velocity, including direction. At equal velocity, greater mass means greater momentum magnitude.

Link to this topic
MomentumThe green p arrow changes length with momentum magnitude and reverses with the velocity sign. m p +−
The green p arrow changes length with momentum magnitude and reverses with the velocity sign.

One-dimensional sign convention: right is positive; left is negative.

Change the parameters
Calculated resultp = 18 kg·m/s

Symbols and SI units

p: momentum, kg·m/s; m: mass, kg; v: velocity, m/s. This p is not pressure.

Unit check

kg × m/s = kg·m/s

When it applies

Use for classical motion. Both p and v are vectors. Signs represent one-dimensional direction; do not add opposite momenta as unsigned magnitudes.

Worked example

3 kg × 6 m/s = 18 kg·m/s. At −6 m/s, momentum is −18 kg·m/s.

Impulse and momentum changeUpper secondary mechanicsJ = FΔt = Δp

The same force acting longer produces a greater impulse. Net external impulse equals the change in momentum.

Link to this topic
Impulse and momentum changeThe green rectangle is a constant-force F–t graph: width is Δt, height is F, and signed area is impulse. Ft0 J = FΔt
The green rectangle is a constant-force F–t graph: width is Δt, height is F, and signed area is impulse.
Change the parameters
Calculated resultJ = 10 N·s

Symbols and SI units

J: impulse, N·s; F: constant or average net external force, N; Δt: interval, s; Δp: momentum change, kg·m/s.

Unit check

N·s = kg·m/s

When it applies

J = FΔt uses constant force, or F as the average net external force over the interval. A varying force generally requires a time integral. Here we use one-dimensional components.

Worked example

20 N × 0.5 s = 10 N·s. Here J is the impulse symbol; J used as a unit elsewhere means joules.

Kinetic energyUpper secondary mechanicsEₖ = ½mv²

Kinetic energy scales with speed squared. At fixed mass, doubling speed quadruples kinetic energy.

Link to this topic
Kinetic energyThe green arrow shows speed v; the lower green bar shows kinetic energy Eₖ. Each uses its own fixed diagram scale. m v Eₖ720 J
The green arrow shows speed v; the lower green bar shows kinetic energy Eₖ. Each uses its own fixed diagram scale.
Change the parameters
Calculated resultEₖ = 54 J

Symbols and SI units

Eₖ: kinetic energy, J; m: mass, kg; v: speed, m/s.

Unit check

kg × (m/s)² = kg·m²/s² = J

When it applies

Classical translational kinetic energy, at speeds much lower than light speed. v is speed magnitude. Energy is a nonnegative scalar; rotational energy is not included.

Worked example

½ × 3 kg × (6 m/s)² = 54 J. Square 6 to get 36 before multiplying by 3 and ½; squaring does not mean multiplying by 2.

Gravitational potential energyUpper secondary mechanicsEₚ = mgh

In the same gravitational field, greater mass or height above the reference means greater gravitational potential energy.

Link to this topic
Gravitational potential energyThe green vertical line marks height h above the dashed reference. The slider changes the object’s height. m hh = 0
The green vertical line marks height h above the dashed reference. The slider changes the object’s height.

Fixed g = 9.8 m/s²; the dashed line is h = 0.

Change the parameters
Calculated resultEₚ = 58.8 J

Symbols and SI units

Eₚ: potential energy, J; m: mass, kg; g: gravitational acceleration, m/s²; h: relative height, m.

Unit check

kg × m/s² × m = J

When it applies

Near Earth’s surface with approximately constant g, after choosing a zero-energy reference. Here h is above that reference. Changing the reference changes Eₚ but not the energy difference between positions.

Worked example

3 kg × 9.8 m/s² × 2 m = 58.8 J. A question specifying g = 10 m/s² gives 60 J instead; state the approximation used.

Work by a constant forceUpper secondary mechanicsW = Fs cos θ

Only the force component along displacement contributes to work. The same force magnitude can do positive, zero or negative work as the angle changes.

Link to this topic
Angle between force and displacementThe green arrow is force F; the grey horizontal arrow is displacement s. θ is measured from the rightward horizontal. Click or drag in the diagram to change the force angle. You can also use the slider below, or focus the diagram and press arrow keys. 180°90°0° s F0°
The green arrow is force F; the grey horizontal arrow is displacement s. θ is measured from the rightward horizontal.

Click or drag in the diagram to change the force angle. You can also use the slider below, or focus the diagram and press arrow keys.

Change the parameters
Calculated resultW = 500 J

Symbols and SI units

W: work, J; F: force, N; s: displacement magnitude, m; θ: angle, entered here in degrees.

Unit check

N × m = J

When it applies

F is constant force magnitude, s is displacement magnitude, and θ is their angle. W = Fs only when θ = 0°. A general varying force requires integration along the path.

Worked example

50 N acting along a 10 m displacement does 50 × 10 × cos 0° = 500 J. At 90°, this force does 0 J of work.

PressureLower secondary reviewp = F⊥ / A

The same normal force spread over a smaller area produces greater average pressure.

Link to this topic
PressureThe green downward arrow shows normal force. Contact width changes with A while depth is treated as fixed. F⊥A
The green downward arrow shows normal force. Contact width changes with A while depth is treated as fixed.
Change the parameters
Calculated resultp = 5000 Pa

Symbols and SI units

p: pressure, Pa; F⊥: normal force, N; A: contact area, m². This p is not momentum.

Unit check

N / m² = Pa; 1 cm² = 0.0001 m²

When it applies

Use the force component normal to the surface and A > 0. This is average pressure over the area; it also equals local pressure when the distribution is uniform.

Worked example

100 N ÷ 0.02 m² = 5000 Pa. 200 cm² = 0.02 m²; area conversion squares the length conversion factor.

Average speedLower secondary reviewv̄ = d / Δt

Total distance divided by total elapsed time gives average speed; it does not describe the speed at every instant.

Link to this topic
Average speedThe green line lays out total distance d, with its endpoint changing with distance. It does not imply constant speed. 0200 m dΔt = 20 s
The green line lays out total distance d, with its endpoint changing with distance. It does not imply constant speed.
Change the parameters
Calculated resultv̄ = 5 m/s

Symbols and SI units

v̄: average speed in this lesson, m/s; d: total distance, m; Δt: total elapsed time, s.

Unit check

m / s = m/s; 1 m/s = 3.6 km/h

When it applies

Δt must be positive. Use distance and elapsed time for the same complete journey. Average velocity uses displacement, so it differs from average speed on a return journey.

Worked example

100 m ÷ 20 s = 5 m/s = 18 km/h. Include any time spent stopped in the total elapsed time.

DensityLower secondary reviewρ = m / V

Density is mass per unit volume. At equal volume, greater mass means greater density.

Link to this topic
DensityThe green cross-section changes with V while depth is treated as fixed. Mass m is independently set by its slider; colour intensity does not encode density. V m = 780 kg
The green cross-section changes with V while depth is treated as fixed. Mass m is independently set by its slider; colour intensity does not encode density.
Change the parameters
Calculated resultρ = 7800 kg/m³

Symbols and SI units

ρ: density, kg/m³; m: mass, kg; V: volume, m³. The volume symbol V differs from the voltage unit V.

Unit check

kg / m³ = kg/m³; 1 g/cm³ = 1000 kg/m³

When it applies

V must be positive, with mass and volume from the same object. m/V gives average density; it equals density throughout only for a uniform object. Density can change with temperature and other conditions.

Worked example

780 kg ÷ 0.1 m³ = 7800 kg/m³. The denominator is volume, not m²; dividing by 0.1 multiplies by 10.

Ohm’s lawLower secondary reviewU = IR

For an ohmic conductor with fixed resistance, voltage is proportional to current.

Link to this topic
Ohm’s lawGrey lines show an ideal closed circuit and resistor R. The green arrow indicates conventional current I and changes length with current. U is the required supply voltage, not heat or brightness. RU+ I R = 10 Ω
Grey lines show an ideal closed circuit and resistor R. The green arrow indicates conventional current I and changes length with current. U is the required supply voltage, not heat or brightness.
Change the parameters
Calculated resultU = 5 V

Symbols and SI units

U: voltage, V; I: current, A; R: resistance, Ω. The unit A means amperes; the area symbol A has a different meaning.

Unit check

A × Ω = V

When it applies

Use for an ohmic conductor with temperature and other physical conditions held fixed. This ideal DC resistor model does not describe a diode or a filament whose temperature changes substantially.

Worked example

0.5 A × 10 Ω = 5 V. At fixed resistance, doubling current doubles the required voltage.

Diagrams show relationships, not a scale model or a motion recording. Green marks the named quantity; grey marks objects, surfaces or references. Use the readouts for exact values.

One quick model check

1A 100 N normal force acts uniformly on 200 cm². What is the pressure?

Observe, then explain

Work through four steps. Each button moves the interactive model to the matching observation state.

  1. Pressure is normal force divided by contact area. Its SI unit N/m² is the pascal. Converting cm² to m² squares the length conversion factor.

    Look for: Open pressure and check why 100 N acting on 200 cm² gives 5000 Pa.

  2. The speed in kinetic energy is squared. For the same mass, changing speed from 3 m/s to 6 m/s quadruples the energy.

    Look for: Open kinetic energy, keep 3 kg, and compare the readouts and energy bar at 3 m/s and 6 m/s.

  3. W = Fs requires constant force along displacement. A perpendicular force has zero cosine and does zero work. A force opposing displacement does negative work.

    Look for: Open work, keep 50 N and 10 m, then set the angle to 0°, 90° and 180°.

  4. Density is mass divided by volume: 780 kg ÷ 0.1 m³ = 7800 kg/m³. Volume cannot be written as m², and division by a decimal must preserve the correct magnitude.

    Look for: Open density, keep 780 kg, and double volume from 0.1 m³ to 0.2 m³. Explain why density halves.

Build an explanation

A symbol needs its context

In momentum, p has units kg·m/s; in pressure, p has units Pa. J can be the impulse symbol or the unit symbol for joules. Writing the quantity name and units prevents identical letters from being mistaken for identical meanings.

Every model has conditions

Fₙₑₜ = ma assumes an inertial frame and constant mass. F in J = FΔt is constant or average net external force. Eₚ = mgh uses nearly constant g near Earth’s surface. A fixed-resistance U = IR relationship applies to an ohmic conductor at unchanged temperature and conditions. Obtaining a number does not prove that the model applies.

Check units and limiting cases

Wrong units can reveal misuse immediately: density is kg/m³, not kg/m²; energy is kg·m²/s², not kg·m/s. Try limiting cases: kinetic energy at v = 0 should be zero; work at θ = 90° should be zero; doubling area at fixed force should halve pressure. Correct dimensions alone do not guarantee correct coefficients or conditions.

Printable worksheet

Understand the concept here, then work independently on the A4 sheets. Practice, calculations and investigation records are included together. Reference answers open only in the parent dialog.

Physics

Secondary physics formula toolkit

Name: __________________Date: __________________
Lesson model reference (schematic, not to scale)

What should you check after remembering an equation?

  1. A 100 N normal force acts uniformly on 200 cm². What is the pressure?

    A. 0.5 Pa B. 50 Pa C. 5000 Pa

  2. An object has mass 3 kg and speed 6 m/s. Which kinetic energy calculation is correct?

    A. ½ × 3 × 6² = 54 J B. ½ × 3 × 6 = 9 J C. 2 × 3 × 6² = 216 J

  3. A constant 50 N force is perpendicular to a 10 m displacement. How much work does this force do?

    A. 500 J B. 0 J C. −500 J

  4. Someone writes the density of 780 kg in 0.1 m³ as 78 kg/m². What is the correction?

    A. Change only the unit to kg/m³ B. Change only the number to 7800 C. Correct both to 7800 kg/m³

  5. A person walks 50 m along a line and returns, taking 40 s altogether. What is their average speed?

    A. 0 m/s B. 1.25 m/s C. 2.5 m/s